PRICING
 |
Hydra Loc
was $160.00
$155.00
Per 5 gallon pail.
|
|
|
Hydra Loc. /NCS-2O Negative Small Kit
was $645.00
$605.00
2 five gallon pails of Hydra Loc. and
1 five gallon pail of NCS-2O Negative.
Additional Handling May Apply
|
|
|
Hydra Loc. / NCS-2O Negative Large Kit
was
$1125.00
$1055.00
3 five gallon pails of Hydra Loc. and
2 five gallon pails of NCS-2O Negative.
Additional Handling May Apply
|
|
| More Information |
|
|
 |
COVERAGE RATES
(Note! rates may vary with porosity)
Hydra Loc – 150 / 200 square feet per gallon / per application.
NCS-2O
Negative – 350 / 400 square feet per gallon / per
application.
A Concrete Sealant
Formulated for solving moisture migration.
Typical Uses for Hydra Loc when you have porous concrete,
a broom finished floor, soft chalking concrete or serious existing
water migration problems. Good for interior or exterior conditions.
- Plant or Office Floors
- Warehouse Floors
- Parking Decks
- Industrial Facilities
- Basement Floors and Poured Walls
- Garage Floors
- Sidewalks and Driveways
- Concrete Patios and Retaining Walls
- Anywhere that you have Concrete, Seal, Protect and Condition with
EOS Hydra Loc
- Stops Dusting and Chalking
- Stops Salt Erosion and Degradation
Everyone Can Enjoy A Dry, Healthy Environment by Waterproofing with Hydra Loc,
a Quick, Easy, Inexpensive, Commercial/Industrial or Do-it-yourself
project. Hydra Loc is a waterproofing concrete
sealer that will never stop working. It becomes a permanent
part of the concrete matrix itself.
Hydra Loc is a two-application process that is simply sprayed onto the concrete
with a low-pressure (garden type) pump sprayer. You don't have
to be afraid to use Hydra Loc in your home
because it is Non-toxic, Non-hazardous and Non-flammable. It
has No VOC’s (Volatile Organic Compounds) - No Solvents. Hydra Loc is
a water-based, fast drying, penetrating concrete sealer that
has no unpleasant odor. Clean-up is with clean tap water.
Hydra Loc does a lot more than just waterproof your concrete. It solves potential
health problems associated with a damp slabs or wet basements.
Migrating moisture creates a breeding ground for mold spores
and mildew not to mention that "damp musty odor"reducing
the chance for hazardous mold growth. Endur-O-Seal can greatly
reduce the health risks associated with the growth of mold
and mildew in your home by reducing the water "wicking" through
the concrete.
Whether you are finishing your basement to convert it into usable living
space or just using it for storage, applying a Endur-O-Seal
concrete waterproofing system will make the area a useable,
pleasant, safe and odor free area.
Hydra Loc is most frequently used in conjunction with
NCS-2O
Negative as a final top coat application.
NCS-2O
Negative is a penetrating, membrane forming sealer that
was designed for securing the seal of concrete walls or floors.
If the homeowner intends on finishing his basement walls Endur-O-Seal
recommends that you purchase Hydra Loc and
NCS-2O
Negative in kit form at a great 10% savings.
PREPARATION
All concrete must be clean, raw concrete, no paint or sealers. To remove
algae spray down with a 50/50 mixture of Clorox and tap water. Deck brush
and hose or mop down to rinse. Allow area to semi dry and apply Hydra Loc with
a inexpensive low-pressure (garden type) pump sprayer that you can use
for both products.
APPLICATION INSTRUCTIONS
Application on Floors
- Floor must be damp before applying Hydra Loc Use clean damp tap water to dampen.
- Fill your sprayer with Hydra Loc and apply a wet application to the floors using
a left- right and then up down motion for optimum coverage. Apply only enough product to create
a shiny wet layer of sealer. Product will penetrate in 7 to 10 minutes. Do not let product puddle,
mop up excess in low place after 10 minutes.
- Apply 2 consecutive wet applications of Hydra Loc 30 to 45 minutes apart while floor
is still damp from the previous application. Use a left-right motion to leave a shiny wet application
of liquid sealer on the surface. Hydra Loc will penetrate the concrete surface in 7
to 10 minutes leaving just a damp looking surface. Reapply the second application while the surface
is still damp for best results. A 3rd. application maybe applied for extra sealing strength if desired.
- Use a deck brush and a liberal amount of water 6 to 12 hours after the last application, vigorously brush
to remove all residual sealer and purged contaminates from all surfaces that are to be painted or have
other coatings or adhesives applied.
- Allow sealer 10 days to cure before applying paint or another topical treatment.
- Allow product to cure the full 10 days before applying NCS-2O Negative.
- Use a dry deck brush and vacuum to remove any purged lime or dust that may be on the surface before
applying NCS-2O Negative.
- Using the same clean sprayer apply NCS-2O Negative in a left to right and then a up
down motion for complete coverage. Allow a maximum of 1 hour for NCS-2O Negative to
begin it's curing process and then repeat a second application. Do not allow the product to puddle
after 20 minutes, mop up excess from low spots.
- After and between applications clean your sprayer with clean tap water, run pressurized water through
the nozzle.
Application on Walls
- Walls must be damp before applying Hydra Loc Use clean damp tap water to dampen.
- Fill your sprayer with Hydra Loc and apply a wet application to the walls spraying from
the top down using a left right and then up down motion for optimum coverage. Apply only enough product
so as not to create run-off of the Hydra Loc A 12 inch sag in the sealer is maximum. Repeat the
application within 30 to 45 minutes.
- Apply 2 consecutive wet applications of Hydra Loc 30 to 45 minutes apart while wall is
still damp from the previous application. Use a left right, up down motion to leave a shiny wet
application of liquid sealer on the surface. Hydra Loc will penetrate the concrete
surface in 5 to 10 minutes leaving just a damp looking surface. Reapply the second application while
the surface is still damp for best results. A 3rd. application maybe applied for extra sealing
strength if desired.
- Use a deck brush and a liberal amount of water 6 to 12 hours after the last application, vigorously brush to remove all residual sealer and purged contaminates from all surfaces that are to be painted or have other coatings or adhesives applied.
- Allow sealer 10 days to cure before applying paint or another topical treatment.
- Allow product to cure the full 10 days before applying NCS-2O Negative.
- Use a dry deck brush and vacuum to remove any purged lime or dust that may be on the surface before
applying NCS-2O Negative.
- Using the same clean sprayer apply NCS-2O Negative in a left to right and then a up
down motion for complete coverage. Allow a maximum of 1 hour for NCS-2O Negative to
begin it's curing process and then repeat a second application. Do not allow the product to puddle.
- After and between applications clean your sprayer with clean tap water, run pressurized water
through the nozzle.
|
